![powerchute business edition login default powerchute business edition login default](https://windows-cdn.softpedia.com/screenshots/APC-PowerChute-Business-Edition_9.png)
The building where this unit is installed does not have air conditioning, but the high in San Diego that day was 71 F, so the room was well below 80 F (27 C). Here’s the event log, showing the “battery disconnected” event at 2:39pm:Īnd here’s the temperature graphed from 4:10am to 4:50pm:Īccording to its specs, the DLA1500 is supposed to operate safely in an environment up to 40 C. The temperature was 40 C when the unit reported “battery disconnected.” Is it a coincidence that 40 C is the temperature at which the fan turns on ( KB article)? Perhaps some safety switch was tripped to disconnect the battery? The fuse between the batteries did not trip. Reviewing the PowerChute data log, I see that the temperature is usually around 30 Celcius (86 Fahrenheit), but starting at about 7:30am, it slowly climbed to 41 C (106 F). I disconnected the two batteries from each other and left them outside overnight to cool.
![powerchute business edition login default powerchute business edition login default](http://floris.verstegen-online.nl/wp-content/uploads/2013/11/PowerChute-Business-Edition-Agent-08.png)
![powerchute business edition login default powerchute business edition login default](https://community.librenms.org/uploads/default/original/2X/c/c1259e302b0c962f9e507e22ce460c9c01639740.png)
And get this: two hours after removing them, the batteries still felt hot! I guess I’m lucky I didn’t have flammable hydrogen gas escaping as this thread says can happen. I finally managed to hook a wrench around the top and pull them out. The plastic pull tab broke off when I tried to pull out the batteries. When I got the battery door open, I could see the batteries bulged somewhat and were very hot. Of greater concern was that the unit was almost too hot to touch.
![powerchute business edition login default powerchute business edition login default](https://beardesign.me/media/5bbbeb8da28855.37020555.png)
For some reason there was no corresponding event in the PowerChute event log. Once I got on site, I found that the “Replace Battery” light was blinking. Of course the battery is not disconnected the connection inside the unit is a very secure clip that can’t just wiggle loose. Github.I got an email from APC PowerChute Business Edition that said simply “Battery Disconnected.” The connected UPS is an APC SmartUPS 1500 model DLA1500 (the Dell equivalent of an SUA1500). Zabbix template for monitoring process apcupsd I made a simple template for the APC Netbotz AP9340, i currently have 2 (RJ45) temperature sensors connected and retrieving the temp and humidity from both. Triggers names contain the last value that cause the trigger so you can see the temp/hum in the alert. LLD of Sensors (Only Temperature and humidity) Trigger Prototypes for recommended 45RH% - 55RH% humidity and 20☌ - 24☌ Temperature Graph Prototypes for Temperature and Humidity.
Powerchute business edition login default download#
Installation: * download the attached template * import this template to your zabbix * create new host * apply imported "Template APC ATS" to new host * set. Template was tested on APC AP7723, included value mapping, using standart MIBs. This is basic template for automatic transfer switches by APC. Contains sane triggers, load status, graphs, etc. All fixed now! This APC Template contains outlet discovery and should work with any managed or switched APC PDU. UPDATE: Uploaded V2 to fix one of the power ratings that was the wrong OID. Some power (W/VAC) items disabled for cosmetic reasons, but still. date was set manualy ´cause I failed to locate it in MIBs. General items and triggers for three phases. īased on numerous APC´s templates (tnx folks!) and lots of digging in PowerNet and Experimental MIBs and in Web-interface of UPS. Created by request from local UPS admin (he´s just too lazzy.
Powerchute business edition login default free#
Some power (W/VAC) items disabled for cosmetic reasons, but still functional - feel free to reuse ´em. Based on numerous APC´s templates (tnx folks!) and lots of digging in PowerNet-MIB.